Acceptance Marking No. "MSHA IC-152/16" must be permanently marked on the product with letters at least 1/4" high and at intervals not exceeding 3 feet. Other types of permanent markings may be used with prior approval of MSHA. The accepted range of
2020/7/15· FLAME-RESISTANT FIRE-SUPPRESSION HOSE COVERS ACCEPTED BY MSHA UNDER CODE OF FEDERAL REGULATIONS, TITLE 30, PART 18, SECTION 18.65 The fire-suppression hose covers shown in this list were tested and accepted as flame
EN853 2SN MSHA IC-84/41 Double Braid Hydraulic hose SAE100 R2 AT/DIN EN 853 2SN Inner Tube: Oil resistant synthetic rubber Reinforcement: two high tensile steel wire braids Cover: Abrasion and weather resistant synthetic rubber Temperature Range:-40 to +100 centigrade
High pressure hydraulic hose. Suitable for conveying petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water glycol based fluids and air. All STAUFF Flex Spiral hose is fully branded Flame Resistant US MSHA approval N0.IC-188
acceptance for listing of flame-resistant cable or hose.” 4.6. Acceptance is defined in 30 CFR, Part 18, Section 18.2 as “written notifiion by MSHA that a cable or hose has met the applicable requirements of this part and will be listed by MSHA as acceptable
Abrasion and ozone resistant synthetic rubber –MSHA approved Note: various covers available Temperature range -40 C to 121 C / -40 F to +250 F Standard Branding Mylar Tape Flexline 4000 DN10 3/8‘‘ WP 280 Bar 4060 PSI MSHA IC-8/17
Flexible isobaric Multispiral Hydraulic Hose –MSHA approved FLEXLINE 4000 Nominal Inside Spiral Outside Working pressure Test pressure Burst pressure Bend radius Weight Ø Ø Ø Ø mm inch mm mm mm bar psi bar bar mm kg/m 10 3/8 9,9 17,4 20,4 280 4060 560 1120 65 0,66
2 PFMU - 18 PFMU - 21 High Pressure Hose High Pressure Hose Construction Inner Tube: Oil resistant synthetic rubber. Reinforcement: Spiraled high tensile steel wire. Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.
MSHA evaluated your appliion for MSHA acceptance of the CHP 107 hose cover. Your appliion carried company code nuer PI-IMH05 and was dated April 25, 2014. This construction and the information provided meet the requirements of the Standard
Designed for use in appliions up to 302 F (150 C) continuous, Flexgard is the only woven textile PET abrasion sleeve treated with our proprietary heat and flame resistant coating technology to protect from hose spray-out failures - MSHA IC-258/00 Certified.
Jiffy Push-On/Push Lock Oil Resistant Multipurpose Rubber Hose is designed to transfer air, mild chemicals, oil, water and refined fuels such as biodiesel, diesel, ethanol and gasoline in appliions to 212 F and 300 psi, Series 7212. WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer and birth defects or other
Jacking Hose High pressure hydraulic hose for jacking appliions Synthetic rubber oil resistant liner and abrasion resistant cover. 2 steel braids 24 C21 Isobaric 210 bar Isobaric (constant working pressure for all sizes) range of hoses exclusive to Pirtek.
Jiffy Push-On/Push Lock Oil Resistant Multipurpose Rubber Hose is designed to transfer air, mild chemicals, oil, water and refined fuels such as biodiesel, diesel, ethanol and gasoline in appliions to 212 F and 300 psi, Series 7212. WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer and birth defects or other
Jacking Hose High pressure hydraulic hose for jacking appliions Synthetic rubber oil resistant liner and abrasion resistant cover. 2 steel braids 24 C21 Isobaric 210 bar Isobaric (constant working pressure for all sizes) range of hoses exclusive to Pirtek.
Appliion Procedures for Acceptance of Flame-Resistant Solid Products Taken into Mines. The following requirements apply to this acceptance. 5. Acceptance Marking No. ''MSHA IC-256/8" must be permanently marked on the product with letters at least 1/4
resistant ozone resistant ozone S.F. 2:1 MSHA MSHA MSHA F E MSHA Alterrnative versions SPECIAL BRAIDED Pg 44 TekSC PLUS medium-high pressure hydraulic lines with instal-lation constraints, return lines and suction lines Pg 45 Tekno 2SC
cover is also flame resistant with an eossed MSHA legend. 4:1 Design factor Tube Black Neoprene Branding PARKER USA 7251 THORO-BRAID® AIR HOSE - WIRE BRAID XXX PSI MAX WP-DE4 FIRE RESISTANT-MSHA IC-123/3 - (DATE CODE) -001
Push-Lok Fire Resistant Cover Multipurpose Hose 250-350 PSI – 821FR Hose Parker''s 821FR hose is a fire resistant hose that has a pressure range of 250-350 PSI, and is amongst the Push-Lok multipurpose hose line which features the widest fluid compatibility, appliion …
Hose Inner Diameter 1-1/4" Hose Outer Diameter 1.83" Inner Tube Material Nitrile Length 50 ft Outer Tube Material Neoprene Performance Low Working Pressure Reinforcement Material 1 Helical Cable Wire - 1 Fiber Braid Specifiion MSHA Accepted -40 F
Compact Hose • EN 857 2SC / ISO11237 Type 2SC – No-Skive Compact hose construction • Compatible with 48 series fittings • Small bend radii • Highly abrasion resistant MSHA accepted 471TC – No-Skive Hose When you need a TOUGH and flexible compact
EN853 2SN MSHA IC-84/41 Double Braid Hydraulic hose SAE100 R2 AT/DIN EN 853 2SN Inner Tube: Oil resistant synthetic rubber Reinforcement: two high tensile steel wire braids Cover: Abrasion and weather resistant synthetic rubber Temperature Range:-40 to +100 centigrade
Pressure washer hose for cold and hot water. Resistant to usual detergents. Not for use with steam appliions. Government Specifiion MSHA IC-46/10 Hose Base Nuer H345 Hose Family Water - Pressure Washer Hose I.D. (in) 0.38 Hose O.D. (in) 0.63
Parker has developed an extensive selection of chemical hoses designed to safely and reliably handle a wide variety of acids and chemicals. Our chemical resistant hose solutions are constructed from only the finest state of the art materials and can withstand the
Acceptance Marking No. "MSHA IC-152/16" must be permanently marked on the product with letters at least 1/4" high and at intervals not exceeding 3 feet. Other types of permanent markings may be used with prior approval of MSHA. The accepted range of
Continental Flame Resistant USMSHA No. 2G-IC-14C/39 Appliions A premium-quality, multipurpose industrial hose with a wide range of appliions in factories, construction,agriculture, quarries, mines, railroads, the oil and gas industry and shipbuilding .